Fender vibro champ silverface dating
If you have a cherished octal power tube or rectifier with a broken keyway, here is a great solution. STYLE MICALEX TUBE SOCKET FOR MINIATURE 9-PIN TUBES. F&T Caps are known for their great stability and reliability. Looks similar to the original Fender part number 0990947000. Medium brown handle strap, made of genuine leather, replacement for Fender "tweed" style amps (as well as other vintage amps).
Perfect for Twin Reverb, Showman and Dual Showman, Quad Reverb, Bassman 100, etc. Founded in 1948 by Heinz Fischer and Alfred Tausche, F&T Capacitors has over 60 years of experience in producing some of the finest capacitors available today.
Input impedance 14.5K ohms, output impedance 4 ohms. Does NOT contain the "Made in USA" script found on some Fender logos. New original Fender reproduction, used in many recent and current model Fenders.
Used on the upper left corner of the grill cloth on most CBS era Fender amps. 4 1/2" wide, the "F" in the logo is about 2 1/2" inches tall. "Flat" Fender logo, with black "tail", cast metal, mounting screws included. New original Fender reproduction, used in many recent and current model Fenders.
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL, SET OF 6. TUBE RETAINER WITH GRIP TEETH, DESIGNED FOR OCTAL TUBES WITH PHENOLIC BASE SUCH AS 6L6 OR EL34. Perfect for Vibrolux Reverb, Vibroverb, Super Reverb, Deluxe Reverb, Pro Reverb, Bassman, Bandmaster Reverb, Tremolux, etc. Fender Electrolytic Capacitor Kits Fender capacitor kits contain all of the main filter, decoupling filter, bias filter and preamp cathode bypass electrolytic capacitors for most amps from the blackface and silverface eras.
Note: Tube shields will not fit over the damper rings, and must be removed from the tubes. Princeton and Princeton Reverb do not need the resistors. Do not install in an amplifier that does not have a standby switch - always use the standby switch in amps so equipped when using the 5SSR.
Bolts screw into a captive nut on the top rail of the chassis, so there are no bottom nuts on these models.
Fender started using these in the very late 70s coincident with the introduction of the "Ultralinear 70 Watt and 135 Watt models" Check your amp for compatibility.
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL. By cleaning the remainder of the broken keyway from the tube base and properly installing this keyway replacement (a little dab of silicone sealant works great to hold it in place), your tube can safely be reinstalled into your equipment. Note: when using an adhesive to secure the keyway to the tube base, DO NOT use a water-based glue. Values available include 10u F/500V, 16u F/475V, 22u F/500V, 47u F/500V, 80u F/450V, 100u F/100V, 100u F/450V, and 220u F/300V. Ruby Gold Capacitors are rated at 105 C for longer life, improved stability in the hot environment of tube amplifiers, and increased protection against electrolyte deterioration. Chrome metal caps - replacement for vintage and reissue Fender amps. Has slight "raised" bump near the center of the handle. 6.5 inches from mounting center to mounting center. HANDLE MOUNTING KIT - FOR STRAP HANDLES Complete set of hardware for mounting one leather style strap handle, including machine screws and T-Nuts.
This is a great kit to replaced all 6 of the tube shields in many Fender amps with 6 preamp tubes. An economical alternative to more expensive tube dampers.
Use two (or three) of these rings around a pre-amp tube to reduce noise and microphonics.
Most reissues and redesigns of medium-size 1960 blackface amps with 4" chassis straps starting in the 1980s use this kit Check your amp for compatibility.
Screw spacing is 4 inches center-to-center, strap length is 4 5/8" end-to-end.